Study on the design of ZnO/PANI composites and the mechanism of enhanced humidity sensing properties

ZnO/PANI composite humidity sensor was prepared by hydrothermal method. The first principles of density functional theory study the sensing mechanism. The calculation shows that the oxygen vacancy on ZnO surface is beneficial to the adsorption of water molecules. The {0 0 0‾1} crystal plane with the largest lattice oxygen number in ZnO has a strong adsorption capacity for water molecules, which is also conducive to improving the humidity sensitivity. PANI is easy to be combined on {0 1‾1 0} plane of ZnO, and it indirectly promotes the growth of {0 0 0‾1} plane, increasing the adsorption of water molecules and the proportion of H⁺ and H₃O⁺ ions. In addition, the N–H group in ZnO/PANI enhances the H⁺ conduction, which further improves the performance of the sensor. The results concluded that the proportion of lattice oxygen in humidity sensor is an important factor of humidity sensor sensitive detection.     

Development of a Chitosan/Nickel Phthalocyanine Composite Based Conductometric Micro-sensor for Methanol Detection

Thin-film composite of chitosan/nickel phthalocyanine (NiPc) was electrochemically deposited on the fingers of interdigitated gold electrodes, applying chronoamperometric polymerization technique. The presence of crystallized NiPc in the chitosan was confirmed by EDX and FTIR analysis. Acetone, ethanol, and methanol gas-sensing properties of the films prepared at optimum conditions were studied at atmospheric temperature, through differential measurements at an optimized frequency of 10 kHz, using a lock-in amplifier. The conductometric sensor presents the highest sensitivity of 60.2 μS.cm⁻¹(v/v) for methanol and 700 ppm as the limit of detection. For validation, the methanol content of a commercial rubbing alcohol was determined.     

Development of in-wheel sensor system for accurate measurement of wheel terrain interaction characteristics

Planetary rovers need high mobility on a rough terrain such as sandy soil, because such a terrain often impedes the rover mobility and causes significant wheel slip. Therefore, the accurate estimation of wheel soil interaction characteristics is an important issue. Recent studies related to wheel soil interaction mechanics have revealed that the classical wheel model has not adequately addressed the actual interaction characteristics observed through experiments. This article proposes an in-wheel sensor system equipped with two sensory devices on the wheel surface: force sensors that directly measure the force distribution between the wheel and soil and light sensors that accurately detect the wheel soil surface boundary line. This sensor design enables the accurate measurement of wheel terrain interaction characteristics such as wheel force distribution, wheel–soil contact angles, and wheel sinkage when the powered wheel runs on loose sand. In this article, the development of the in-wheel sensor system is introduced along with its system diagram and sensor modules. The usefulness of the in-wheel sensor system is then experimentally evaluated via a single wheel test bench. The experimental results confirm that explicit differences can be observed between the classical wheel model and practical data measured by the in-wheel sensor system.     

Electrochemical Sensing of Uric Acid Using Glassy Carbon Modified with Multiwall Carbon Nanotubes Dispersed in Polyethylenimine

This work reports the advantages of using glassy carbon electrodes modified with multiwall carbon nanotubes (MWCNT) dispersed in polyethylenimine (PEI). The presence of MWCNTs wrapped by PEI largely facilitated the strong adsorption of uric acid (UA) and allowed its highly sensitive and selective quantification even in the presence of high excess of ascorbic acid. The selected conditions for the electrochemical sensing were 5 s accumulation at ?0.300 V under stirring and quantification in a 0.050 M phosphate buffer solution pH 7.40 by differential pulse voltammetry adsorptive‐stripping after medium exchange. The platform allowed the successful application in the quantification of UA in urine.     

Monitoring the manufacturing process of glass fiber reinforced composites with carbon nanotube buckypaper sensor

Buckypapers are free-standing porous mats of entangled CNT ropes cohesively bounded by van der waals interactions, and can be used to monitor the manufacturing process of glass fiber reinforced composite. In this paper, the buckypaper (BP) was fabricated with monodispersion of multi-wall carbon nanotubes via spray-vacuum filtration, and its morphology and pore size distribution were characterized by scanning electron microscope and nitrogen adsorption/desorption. The resistance of the BP sensor was obtained using a four-point probe method, and the resistance changes could be related to phase changes of the resin matrix,. Experimental results show that the BP sensor embedded in the glass/epoxy composite laminates has indicated a relative resistance change from −2.9% to 226.5% during the manufacturing process. In addition, the temperature sensitivity of a pristine BP sensor and a BP sensor embedded in composite were also characterized. The results demonstrate that the effect of resin phase changes on the resistance changes of a BP sensor is greater than that of the temperature during composite manufacturing.     

O3 and SO2 sensing concept on extended surface of B12N12 nanocages modified by Nickel decoration: A comprehensive DFT study

Adsorption of SO₂ and O₃ molecules on pristine boron nitride (B₁₂N₁₂) and Ni-decorated B₁₂N₁₂ nano-cages has been systemically investigated through density functional theory (DFT) methods. Adsorption energies (thermodynamics), bond distances, charge analysis, dipole moments, orbital analysis and density of states are calculated by van der Waals DFT method (MPW1PW91) functional. The adsorption energies of O₃ and SO₂ on pristine B₁₂N₁₂ are about −143.8 and −14.0 kJ mol⁻¹, respectively. The interaction energies of O₃ and SO₂ with pristine B₁₂N₁₂ are indicative of chemisorption and physisorption, respectively. Ni-decorated B₁₂N₁₂ (Ni@BN) enhances adsorption of both O₃ and SO₂ species. The interaction energies for adsorption of SO₂ are about −166 and −277 kJ mol⁻¹ whereas the corresponding energies for O₃ are −362 and −396 kJ mol⁻¹ for configuration A and B, respectively. These observations show that functionalized B₁₂N₁₂ are highly sensitive toward SO₂ and O₃ molecules.     

Detection of acetone in the human breath as diabetes biomarker based on PPy/WO3 nanocomposite sensor by FFT continuous cyclic voltammetry method

This research represents a novel detection method of acetone level in the exhaled breath samples (RH=88 %) based on polypyrrole/tungsten oxide (PPy/WO₃) nanocomposite sensor. The PPy/WO₃ sensor was fabricated by the deposition of nanocomposite on/between interdigitated electrodes (IDEs) through electrospray coating and was then characterized by FE-SEM imaging. In this detection method, the coulometric signal of the sensor was calculated using Fast Fourier Continuous Cyclic Voltammetry (FFTCCV), where cyclic voltammetry (CV) was applied to the sensor in the defined potential rang and then charge changes of the sensor was obtained by integration of the current in all scanned potential ranges. FFTCCV method enhances the sensitivity of the sensor when exposed to the gas mixtures containing acetone. In addition to its fast coulometric response time (≤5 s) in the two linear ranges of 0.7–2.8 ppm and 2.8–28.2 ppm (R²=0.99), FFTCCV method provides the low detection limit of 70 ppb, and high sensitivity toward acetone at the optimum values of the parameters. The fabricated sensor showed great selectivity toward acetone when exposed to humid air and some exhaled gas like carbon dioxide, ammonia, methanol, ethanol and alkyl amines. The results were very satisfying as the sensor was capable to detect different acetone levels in human exhaled breath as non-invasive diagnosis of diabetes with a good correlation (R²≃0.9) to the routine blood sugar test taken by different commercial glucometers results.     

Sensitive Electrochemical Detection of Thiabendazole in Fruits Using Ag−MoS2 Electrode

Herein, Ag nanoparticles (NPs) modified MoS₂ (Ag−MoS₂) was applied to the surface of glassy carbon (GC) to produce a robust electrochemical sensor for the detection of thiabendazole, a common antifungal in the post-harvesting of fruits. Cyclic voltammetry studies confirmed thiabendazole exhibited an irreversible, diffusion-controlled process on Ag−MoS₂ with a two-fold increase in peak current than the pristine MoS_2. A square wave voltammetry was used for the detection of TBZ. The developed sensor exhibited a linear range between 1–10 μM with LOD down to 0.1 μM (S/N>3). Analysis of TBZ in mango and banana matrices gave a recovery of 91.6–100.4 % indicating the suitability of the sensor for food safety monitoring.     

A Photoelectrochemical Sensor for Firstly the Detection of Amlodipine Besylate Based on an MnC4Pc Coated ZnO Composite Materials

In this study, tetracarboxylic manganese phthalocyanine coated nano-zinc oxide (MnC₄Pc-ZnO) composite material was prepared by in-situ growth method and modified with indium tin oxide (ITO) glass electrode to construct a photoelectrochemical (PEC) sensor. A PEC sensor for the determination of amlodipine besylate (AB) was developed for the first time based on the principle of precipitation reaction between heavy metal ions and dihydropyridine and the recombination suppression effect of the material. The morphology and optical properties of the MnC₄Pc-ZnO composites were characterized by scanning electron microscopy (SEM) and ultraviolet-visible diffuse reflectance spectroscopy (UV-vis DRS). Chronoamperometry (i-t) and electrochemical impedance spectroscopy (EIS) were used to study the PEC behavior of ITO electrodes modified by MnC₄Pc-ZnO composite material. The study found that the MnC₄Pc-ZnO composite material has a good photocurrent response to AB, and there was a good linear relationship between the concentration range of 75 nM-250 μM, the linear equation was I(μA)=−5.2×10⁻⁸×lgC+3.2×10⁻⁸ (r=0.9947), a limit of detection (LOD) of 20 nM. In addition, MnC₄Pc-ZnO/ITO also has good selectivity and stability. The PEC sensor detects amlodipine besylate tablets, amlodipine besylate dispersible tablets, and biological samples, with standard addition recovery rates of 96.11 % and 103.96 %, respectively. The determination result has good accuracy, and the PEC sensor provides a new method for detecting AB.     

Determination of Mercury with a Miniature Sensor for Point-of-care Testing

In developing countries, subsistence gold mining entails mixing metallic mercury with crushed sediments to extract gold. In this approach, the gold−mercury amalgam is heated to evaporate mercury and obtain gold. Thus, the highly volatile mercury can be absorbed through inhalation, resulting in adverse health effects. Urinalysis can be used to detect mercury, which is excreted in urine and feces, and correlate exposure with toxic effects. The current gold standard analytical methods are based on fluorescence or inductively coupled plasma mass spectrometry methods, but are expensive, time consuming, and are not easily accessible in countries where testing is needed. In this work, we report on a miniature electrochemical sensor that can rapidly detect mercury in urine at levels well below the US Biological Exposure Index (BEI) limit of 50 ppb (μg/L). The sensor is based on a thin-film gold electrode and anodic stripping voltammetry electroanalytical approach. The sensor successfully detected mercury at trace levels in urine, with a limit of detection of ∼15 ppb Hg in the linear range of 20–80 ppb. With the low-cost disposable sensors and portable instrumentation, it is well suited for point-of-care applications.